EN 50153-2002 铁路设施.铁路车辆.电器意外的防护规定
时间:2024-05-18 01:39:24 来源: 标准资料网 作者：标准资料网 阅读：8051
【英文标准名称】:Railwayapplications-Rollingstock-Protectiveprovisionsrelatingtoelectricalhazards;GermanversionEN50153:2002
【原文标准名称】:铁路设施.铁路车辆.电器意外的防护规定
【标准号】:EN50153-2002
【标准状态】:现行
【国别】:
【发布日期】:2003-07
【实施或试行日期】:2003-07-01
【发布单位】:欧洲标准学会(EN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:测定;安全工程;安全;电气工程;防电击;电子工程;安全要求;铁路;接触安全装置;电的;规范(验收);电气安全;电动汽车;保护措施;电车道;事故预防;危险;铁道车辆;尺寸选定;交通车辆;铁路设施;运载工具;定义;设备;电驱动装置;电压范围;公共汽车;铁路车辆;电力设备;铁路电力牵引装置
【英文主题词】:Accidentprevention;Buses(vehicles);Contactsafetydevices;Danger;Definition;Definitions;Determination;Dimensioning;Electricrailways;Electrical;Electricalengineering;Electricalinstallations;Electricalsafety;Electrically-operateddevices;Electromobiles;Electronicengineering;Equipment;Protectionagainstelectricshocks;Protectivemeasures;Railwayapplications;Railwayelectrictractionequipment;Railwayvehicles;Railways;Rollingstocks;Safety;Safetyengineering;Safetyrequirements;Specification(approval);Trafficvehicles;Vehicles;Voltagerange
【摘要】:
【中国标准分类号】:S35
【国际标准分类号】:13_260;45_060_01
【页数】:31P.;A4
【正文语种】:英语
【英文标准名称】:Fibreopticinterconnectingdevicesandpassivecomponents-Basictestandmeasurementprocedures-Tests-Mouldgrowth
【原文标准名称】:光纤互联装置和无源部件.基本试验和测量程序.长霉试验
【标准号】:BSEN61300-2-16-1997
【标准状态】:作废
【国别】:英国
【发布日期】:1997-10-15
【实施或试行日期】:1997-10-15
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:试验条件;真菌门;光电子器件;电子设备及元件;耐霉性试验;培养(生物);详细规范;光学测量;纤维光学连接器;纤维光学;光学纤维
【英文主题词】:Glassfibrecables;Measuringtechniques;Mouldgrowth;Opticalwaveguides;Testing
【摘要】:ThepurposeofthispartofIEC1300istodeterminetheeffectsofmouldgrowthontheopticalandmechanicalpropertiesofafibreopticdevice.Itinvestigatesunforeseencausesofdeteriorationinspecimens,whetherornottheseareconstructedfrommould-resistantmaterials,bytheapplicationofeitheroftwotestvariantsasprescribedseverities.
【中国标准分类号】:L23
【国际标准分类号】:33_180_20
【页数】:10P.;A4
【正文语种】:英语
Product Code:SAE J1939/82
Title:Compliance--Truck and Bus
Issuing Committee:Truck Bus Control And Communications Network Committee
Scope:The purpose of these compliance procedures is to generate one or more test documents that outline the tests needed to assure that an ECU that is designed to operate as a node on a SAE J1939 network would do so correctly. SAE does not certify devices and these tests and their results do not constitute endorsement by SAE of any particular device. These tests are presented to allow testing of a Device to determine self-compliance by the manufacturer of a device. The manufacturer can use its record of what procedures were run successfully to show the level of compliance with SAE J1939.